Lever Pump
The Waterra Lever Pump was designed to provide operators with a convenient, portable mechanism which would provide some mechanical advantage when manually operating the Inertial Pump as well as facilitating the collection of samples with this system. This actuator will fasten onto most above ground well completions quickly and easily.
More info
The tubing clamp is designed to accept both Standard Flow and High Flow tubing and the handle is adjustable in order to accommodate approximately 7 pounds. This actuator is the best choice for the occasional light duty user of the Inertial Pumping System.
Key features
Lightweight (8 lbs)
Portable
Rugged field construction
Power: 0 - 3.75 GPM / 200 feet + depth
F&W 6" Submersible Pumps
PVC Plus Drilling Products supplies both 4" & 6" F&W submersible pumps.Available in capacities ranging from 5-50 horsepower. the 6P series is a high capacity 6" submerisble for commercial, municipal, industrial and agricultural applications. Any water well requiring a high capacity output and having a 6" or larger casing, can be matched to one of F&W's quality submersibles. If you need more than 120 GPM, The 6T series of 6" Turbine submersibles will fill the bill.
F&W 4" Submersible Pumps
PVC Plus Drilling Products supplies both 4" & 6" F&W submersible pumps. The 4" submersible pump is available in capacities ranging from 1/2 - 5 horsepower.
Powerpump 2
The PowerPump 2 is the most powerful pump actuator manufactured by Waterra. A Honda G100, 2.5 horsepower, 4 stroke gasoline motor powers this device. This actuator generates a 6 inch stroke and can operate both the Standard Flow System and the High Flow System to their maximum effective depths.
More info
The PowerPump 2 weighs 70 pounds and usually requires two people to carry it. This actuator is an excellent choice for those with extreme pumping requirements.
Key features
Portable
Power: 0 - 3.75 GPM / 250 feet + depth
Rugged field construction
Hydrolift II
The Waterra Hydrolift II is a portable, electrically operated device that is used to automate the operation of the Inertial Pump. The Hydrolift is powered by a 3/4 horsepower electric motor (available in either 110 volt or 220 volt) and generates a 4 inch stroke at up to 200 cycles per minute. This actuator can operate the Standard Flow System up to its maximum effective depth and will operate the High Flow System up to a depth of 150 feet.
More info
The Hydrolift weighs 35 pounds and requires an electrical power supply of at least 1000 watts. This actuator is the ideal choice for the frequent user of the Inertial Pumping System with moderate to extreme pumping requirements.
Key features
Lightweight
Rugged field construction
Power: 0 - 3.75 GPM / 200 feet + depth
Model 407 Integra Bladder Pump
The Model 407 Integra Bladder Pump is excellent for high quality VOC sampling. It allows consistent high quality samples from all types of applications.
The Teflon® bladder is very easily replaced in the field. All components are easy to disassemble for thorough decontamination.
Model 408 Double Valve Pump
The Model 408 Double Valve Pump is a gas drive pump suitable for applications up to 2,000 ft. (600 m) deep, and narrow diameters. A variety of sizes are available, including a 1.5" (38 mm) and narrow 5/8" (16 mm) diameter models. The Model 408 converts easily into a Bladder Pump, if desired.
Grundfos Redi-Flo2 Pump
The Grundfos Redi-Flo2® Pump is an electric submersible pump well known for its high purge rates and ability to reduce to a low flow for sampling.
The pump is designed to fit inside a standard 2" monitoring well. The variable frequency drive converter will work with either 115 or 230 volt electrical supply.